Magellan Paradox Instalační manuál stáhnout pdf (Strana 13)

Paradox Magellan Systems 13

Programming Methods

WinLoad Installer Upload/Download

Software

Program the Magellan console remotely or on-site using the

WinLoad Installer Upload/Download Software for Windows®. For

more information, contact your local Paradox Distributor or visit

our Web site at www.paradox.ca. If you are using the WinLoad

software, you must program the features explained on pages 35.

Please refer to WinLoad’s Online Help for more

information on using WinLoad.

Programming Using the Built-in Keypad

Use the built-in keypad to access Magellan’s programming

mode.

Use the supplied Magellan Programming Guide to keep

track of which sections were programmed and how.

To access programming mode:

1. Press and hold the [0] key.

2. Enter your [

INSTALLER CODE] or [MAINTENANCE CODE].

3. Enter the 3-digit [SECTION] you wish to program.

4. Enter the required [DATA].

There are two methods that can be used to enter data when in

programming mode; Single Digit Data Entry and Feature Select

Programming methods.

Single Digit Data Entry Method

After entering programming mode, some sections will

require that you enter decimal values from 000 to 255. Other

sections will require that you enter hexadecimal values from

0 to F. The required data will be clearly indicated in this

manual as well as in the Magellan Programming Guide.

When entering the final digit in a section, Magellan will

automatically save and advance to the next section. Table 1

(see below) shows the keys and their equivalent decimal

and/or hexadecimal value.

Table 1: Decimal and Hexadecimal Values

* CK = Center keypad

Feature Select Programming Method

After entering certain sections, eight options will be

displayed where each option from [1] to [8] represents a

specific feature or option. To manipulate the options:

• Press the key corresponding to the desired option and

the option number will appear in the LCD display. This

means the option is ON. Press the key again to remove

the digit from the LCD display, thereby, turning OFF the

option.

• Press the [*] key to set all eight options to OFF. Press

the keys until the current section’s options are set. When

the options are set, press the [#] key to save and

advance to the next section.

• Press the [*] key twice to exit without changing any data.

Programming Using a Paradox Memory Key

The Paradox Memory Keys (PMC-3) are very useful when

multiple Magellan consoles are to be programmed identically.

Rather then programming each console by entering its

programming mode and then scrolling through programming

sections, use a memory key to program each console. The

programming of a console with a memory key takes

approximately three seconds.

There are two actions that can be performed with a memory key.

Download Data to Destination Console

To download the data of a memory key into a console:

1. Remove power from the Magellan console (AC and bat-

tery) and connect the memory key to the 5-pin connector

on the left side of the back of the console (see Figure 8

on page 10).

2. Re-apply both AC and battery power to the console.

3. Press the [

ok] key and Magellan will begin downloading

the data from the memory key.

Copy Data to Memory Key from Source Console

To copy the contents of a console into the memory key.

1. Remove power from the Magellan console (AC and bat-

tery) and connect the memory key to the 5-pin connector

on the left side of the back of the console (see Figure 8

on page 10).

2. Re-apply both AC and battery power to the console.

3. Press the [

next] key and then the [ok] key. Magellan

will begin copying its data into the memory key.

The installer code of the Magellan console used to

download data to

the memory key must be the same

installer code programmed in the Magellan console that is

to download the contents from

the same memory key. If the

installer codes do not match, the contents of the memory

key cannot be downloaded into the receiving console.

Example: The contents of the Magellan console A will be

copied into memory key B. The installer code for console A

is 111111. In order to download the contents of memory key

B into the Magellan console C, the installer code

programmed in console C must also be 111111.

Key Value Key Value

[1] 1 [9] 9

[2] 2 [0] 0 (decimal)

Space (Hexa decimal)

[3] 3 [1] CK* A (Hexadecimal only)

[4] 4 [2] CK* B (Hexadecimal only)

[5] 5 [3] CK* C (Hexadecimal only)

[6] 6 [4] CK* D (Hexadecimal only)

[7] 7 [5] CK* E (Hexadecimal only)

[8] 8 [6] CK* F (Hexadecimal only)

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 44 45

Komentáře k této Příručce

Žádné komentáře

Magellan Paradox Instalační manuál Strana 13

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Magellan Paradox