Magellan MG5000 Instalační manuál stáhnout pdf (Strana 24)

20 Reference & Installation Manual

5.9 Zone Timers

Sections [041] to [044]: Zones 1 to 4

001 to 255 X 10ms, Default = 060

The Zone Timer defines how quickly the control panel will respond to an open zone. The control panel will not display an open

zone on the keypad or generate an alarm until the programmed Zone Timer has elapsed. All other zone definitions and options

do not come into effect until the Zone Timer has elapsed. This feature prevents any momentary glitches from causing an alarm or

unnecessary reporting.

Part 6: Wireless Features

The Magellan MG5000 allows for the addition of up to thirty-two fully supervised Magellan wireless transmitters, and up to thirty-two

programmable remote controls.

6.1 Wireless Transmitter Programming

The programming of the wireless transmitters (detectors and door contacts) is accomplished in two steps:

1. Assign the wireless transmitter to the Magellan MG5000.

2. Program the zones.

Wireless Transmitter Programming can be executed through the Installer Quick Menu in the MG5000 Programming Guide.

Sections [061] to [092] represent expansion inputs 1 to 32 respectively.

The serial number is located on the inside of the transmitter or you can use the Serial Number Display (section [960]) to

determine its serial number. The transmitters must be activated once having been assigned to the Magellan MG5000. To

activate a transmitter, insert the batteries and close the cover. To ensure proper synchronization between the control panel

and the transmitter, open and close the zone corresponding to the transmitter.

6.2 Viewing the Wireless Transmitter Signal Strength

Sections [101] to [132]

Once wireless transmitters have been installed and assigned to the Magellan MG5000, the signal strength of each transmitter

can be verified in sections [101] to [132]. Each section represents the signal strength viewer for a specific device. For example,

section [101] is the viewer for zone 1 and section [132] is the viewer for the zone 32. Sometimes moving the transmitter or control

panel by a small amount will greatly increase the signal reception.

How Do I Assign Wireless Transmitters to the MG5000?

1) Press the [ENTER] key.

2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)

3) Enter the desired [SECTION NUMBER] (from sections [061] to [092]).

4) Enter the 6-digit [

SERIAL NUMBER] of the wireless transmitter.

How Do I Delete Assigned Wireless Transmitters?

1) Press the [ENTER] key.

2) Enter your [INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)

3) Enter the desired [

SECTION NUMBER] (from sections [061] to [092]).

4) Press the [0] key six times to clear the serial number.

How Do I View a Wireless Transmitter’s Signal Strength?

1) Press the [ENTER] key.

2) Enter your [

INSTALLER CODE] (default: 0000 / 000000) or [MAINTENANCE CODE] (default 1111/111111)

3) Enter the desired [

SECTION NUMBER] (from sections [101] to [132]).

4) Press the transmitter’s anti-tamper switch or open the corresponding zone.

5) The keypad will illuminate numbers 1 to 10.

Signal Strength Indicator

8 to 10 / 3 beeps = Best signal 5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 55 56

Komentáře k této Příručce

Žádné komentáře

Magellan MG5000 Instalační manuál Strana 24

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Magellan MG5000